Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The San Antonio Owner’s Guide
CGI kitchen remodeling in San Antonio typically runs $14,000 to $45,000 installed, depending on cabinet scope, countertop material, and whether layout changes are involved. We stock and install CGI-compatible kitchen components across the metro, and most homeowners reach out to us after discovering their CGI cabinetry or hardware has warped, delaminated, or started sagging in the Texas humidity. The usual discovery path looks like this: a drawer face that won’t stay flush, a finish that’s clouded over, or a hinge that’s given up entirely. If you’re reading this, you probably already know the part that failed. The good news is we carry what you need and we’re not going to make you chase it down.
The Relay Visibility Guarantee applies here the same way it does on a full kitchen gut: written price before any work starts, live arrival time, and photo updates while we’re in your home.
Which CGI Models This Applies To
CGI kitchen lines vary enough that ordering a part blind is a fast way to waste money. The brand’s cabinetry series uses two common hinge boring patterns, and they are not interchangeable. Older CGI cabinet boxes typically run a 35mm cup bore with a 1/2-inch overlay, while the more recent slim-shaker line shifted to a 9/16-inch overlay. That 1/16-inch difference is enough to make a door hang crooked, and we see it happen often when homeowners order a replacement hinge online without measuring. The plate width matters too: CGI has used both 26mm and 32mm mounting plates depending on the series year.
When we come out, we pull the hinge or drawer slide first and read the stamp on the back. Most CGI hardware carries a two-letter series code that tells us the generation and the boring standard. We match OEM when the part is still available, and if it’s discontinued – which happens with older CGI lines – we carry quality aftermarket equivalents that match the bore pattern, overlay, and plate mounting. The decision on OEM versus aftermarket comes down to this: for hinges and slides, an aftermarket part matched correctly will perform as well. For door faces and drawer fronts, OEM is the only call, because a mismatched finish on a cabinet face is something you’ll see every single day.
Styles & brands we work with
Signs Your CGI Kitchen Remodeling Is Failing
- Cabinet doors that no longer sit flush against the frame. In San Antonio’s humidity swings, CGI cabinet boxes can expand just enough to throw the hinge alignment off. It starts subtle – a door that lists a quarter inch – and worsens as the hinge plate loosens under repeated stress.
- Soft-close hinges that slam or stick. The damper inside a CGI soft-close hinge is a small fluid-filled cylinder, and once it leaks, the hinge loses the slow-close function entirely. Texas summers accelerate the failure because heat degrades the internal seal.
- Finish clouding or peeling on door and drawer fronts. Steam from cooking and the constant San Antonio humidity work their way into the finish layer. We see this most on lower cabinets near dishwashers, where heat and moisture hit the same doors daily.
- Drawers that catch, drag, or pop off their slides. CGI drawer slides depend on nylon wheels or ball bearings, and both wear unevenly. A drawer that catches halfway usually means a bearing has flattened or a wheel has cracked.
- Warped or swollen panels, particularly on sink base cabinets. One slow leak under the sink is enough to swell a CGI cabinet panel permanently. The damage isn’t reversible, but the panel can be replaced without tearing out the entire run.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Kitchen remodeling work on CGI cabinets and components in San Antonio typically runs $14,000 to $45,000, and the range mostly reflects how much of the kitchen we’re touching. Replacing a full set of CGI cabinet fronts and hardware on an average 10×12 kitchen lands in the $14,000 to $22,000 range. A complete gut-and-rebuild with new CGI cabinetry, countertops, and backsplash pushes toward the $30,000 to $45,000 top end. Smaller-scope work sits under the remodels:
- Cabinet installation: $4,000 to $13,000
- Countertop installation: $2,000 to $6,500
- Backsplash installation: $800 to $2,500
- Kitchen island installation: $3,000 to $10,000
Every quote we write is a written line-item price. You’ll see parts cost, labor cost, and material runs separated so there’s no mystery at the invoice. The 365-Day Done Right Promise covers our install work in writing, and if a part we installed fails inside that year, we come back and make it right.
DIY or Call Us?
Replacing a hinge or swapping a drawer slide on a CGI cabinet is within reach for a careful homeowner. Check the hinge stamp first, measure the overlay with the door off, and make sure the mounting plate matches. Where DIY goes wrong is on anything involving cabinet boxes, panel replacement, or finish matching. A misdrilled hinge cup in a CGI door means replacing the whole door, and a finish mismatch on a single panel will make the entire kitchen look off. The other honest note: if a cabinet is pulling away from the wall or the box itself is compromised, that’s a structural problem, and that’s where you want someone who’s done this a few hundred times. Call (432) 547-6806 and we’ll take a look. The estimate is free, and the price we write down is the price you pay.
FAQs
CGI kitchen cabinets in San Antonio typically last 15 to 20 years before finish or hardware failures become frequent, though the Texas humidity shortens that for unsealed panels and cheap hinges. Cabinets near dishwashers and sinks usually show wear first. Call (432) 547-6806 and we’ll assess what needs replacing and what has years left in it.
Hinges, slides, and hardware can generally be replaced outright, while warped panels and delaminated finishes usually need a new part rather than a repair. A soft-close hinge with a blown damper is not worth rebuilding – the replacement is cheaper than the labor to fix it. For an honest read on what’s salvageable, call us for a free assessment.
Swapping hinges and slides across a full CGI kitchen typically takes one to two days, depending on the number of doors and drawers and whether any panel replacement is needed. We stock common CGI-compatible hardware on the truck, so most jobs don’t require a second visit. Call (432) 547-6806 and we’ll give you a straight answer on timeline.
We stock the most common CGI hinge sizes, mounting plates, and drawer slides, including aftermarket equivalents for discontinued CGI lines. For less common door faces and panels, we order from our supplier network – which also covers KraftMaid, Cambria, and Silestone – and coordinate the install once everything’s in. If you need a match, call us and we’ll check stock while you’re on the phone.
Written by Luca Romano, Owner, Sawyer Remodel San Antonio at Sawyer Remodel San Antonio, serving San Antonio and nearby areas.
