Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Roofing: The San Antonio Owner’s Guide
If you’re holding a failed KraftMaid roofing component and want it matched, priced, and swapped without a runaround, here’s the short version: we stock KraftMaid-compatible roofing parts on the truck and install them across San Antonio for $400 – $1,800 depending on the damage. The roofing failures we see most often in Bexar County aren’t KraftMaid-specific engineering problems – they’re what San Antonio summers and hail seasons do to any roofing system. Owners usually discover the problem the same way: a water stain on the ceiling after a storm, a missing shingle in the yard, or roof flashing that’s pulled away from the chimney. You don’t need a new roof. You need the failed part identified and replaced correctly.
Note we’re an independent roofing and remodeling contractor in San Antonio – we work with KraftMaid-compatible parts daily, but we’re not a KraftMaid company or an official KraftMaid dealer. That independence means we match what’s actually on your roof, not what a single brand’s catalog says you should have.
Key Takeaways
- KraftMaid roofing failures in San Antonio are usually flashing, underlayment, or sealant problems – not full roof failures.
- Installed repair costs run $400 – $1,800 in this market; full replacements run $8,000 – $20,000 if the damage has spread.
- We stock common KraftMaid-compatible flashing, sealant, and shingle-match components on the truck.
- Roof work is genuinely dangerous. We’ll tell you what’s safe to check yourself and what isn’t.
- You get a written price before work starts. No weather-inflated surprises, no “while we’re up there” add-ons.
Which KraftMaid Models This Applies To
KraftMaid is known for cabinets, but the roofing line that’s out there – mostly in homes built between 2005 and 2018 – uses a specific spec pattern that matters when you’re matching parts. The compatibility gotcha: KraftMaid roofing components from the 2000s used a 26-gauge galvanized flashing profile that doesn’t always match the thicker 24-gauge material common on newer San Antonio roofs. If a contractor slaps a generic 24-gauge flashing piece on a 2000s-era KraftMaid system, the metal gauges don’t seat properly against the shingle profile, and you get a leak that starts small and grows fast. That’s why we check gauge and profile on-site before quoting anything.
Look for a small stamp or label on the underside of any failed flashing, drip edge, or vent collar. KraftMaid roofing parts from the Texas distribution era (roughly 2004 onward) carry a three-letter series code: KMR, KMP, or KMX. The KMR is the residential spec, the KMP is the heavier-gauge pro line used on steeper pitches, and the KMX was a limited custom run. If you can’t find a label, we identify the part by measurement and shingle profile on-site. For OEM versus aftermarket: KraftMaid-branded roofing parts are still available through a few distributors, but aftermarket equivalents from GAF, Owens Corning, and CertainTeed – all of which we carry – are usually $15 – $40 cheaper per component and carry equal or better warranty backing. For a failed flashing or vent collar, the aftermarket path is usually the smarter buy. We’ll quote both if you want the choice.
Styles & brands we work with
Signs Your KraftMaid Roofing Is Failing
- Water staining on the ceiling after a San Antonio storm. This is the classic flashing failure: rain finds the seam where the KraftMaid flashing meets the vent pipe or chimney, and the water runs inside. It doesn’t mean your whole roof is shot – it means one seam opened up. Fix the seam, and the leak stops.
- Shingles or shingle fragments in the yard after wind. The adhesive strip on the underside of a shingle degrades in Texas heat, and wind does the rest. If you’re finding pieces of shingle, count the bare spots – one or two missing shingles is a $400 – $600 repair. Twenty missing shingles is a much bigger conversation.
- Roof flashing pulled away from the chimney or sidewall. San Antonio’s temperature swings – freezing nights in January, 100-degree days in July – expand and contract metal flashing until the sealant between the flashing and the structure fails. When you see a visible gap, water is already getting in.
- Granules in the gutter or downspout. The ceramic coating on shingles wears down over time, and the granules wash into your gutters. Some granule loss is normal after year ten; a steady stream of granules after a single rain means the shingle’s protective layer is essentially gone, and the shingle is baking unprotected.
- Soft spots you can feel from inside the attic. If you can push up on the roof decking and it flexes more than it should, the underlayment has been wet long enough to start compromising the wood itself. That’s past the “patch it” stage and into the “we need to cut out and replace the decking section” stage.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed KraftMaid roofing repair in San Antonio runs $400 – $1,800 depending on what failed and how much flashing or shingle area needs replacing. Here’s the line-item reality:
- Flashing repair or replacement: $400 – $900 (typical: chimney flashing, vent pipe collar, drip edge)
- Shingle replacement (1 – 10 shingles): $400 – $700 (typical: wind damage, spot hail damage)
- Underlayment patch plus shingle reset: $600 – $1,100 (typical: leak has been active but decking is sound)
- Vent collar or boot replacement: $400 – $800 (typical: cracked rubber boot from heat exposure)
- Full roof replacement: $8,000 – $20,000 (only if the damage has spread beyond any reasonable patching – we’ll tell you if you’re not there yet)
Every quote includes the part, the labor, disposal of the old material, and our written warranty on the repair. If the repair fails within a year, the 365-Day Done Right Promise kicks in – we come back and fix it, covered in writing. The price we put in front of you before work starts is the price on the invoice. No change orders mid-job, no weather surcharges.
DIY or Call Us?
What’s safe to check yourself: you can inspect the attic for water staining, look at your gutters for granules, and eyeball your flashing from the ground with binoculars. You can also clear leaves and debris from your gutters so water isn’t backing up under the shingle line – that’s a maintenance task any San Antonio homeowner can handle safely. What’s not safe: climbing onto the roof. KraftMaid roof pitches in this market run 4:12 to 8:12 on most homes, and a fall from an 8:12 pitch in the wrong shoes is a trip to University Hospital. High-heat work on shingle adhesive strips also requires knowing the right temperature window – too hot and the shingles tear when you lift them, too cold and the adhesive won’t cure. And any repair around a vent pipe or chimney means working at height adjacent to gas lines. That’s not a Saturday-afternoon video tutorial; that’s a call to us. If you’re unsure whether your issue is minor or structural, call (432) 547-6806. We’ll come out, assess it, and give you the written price – and if it’s something you can safely handle yourself, we’ll tell you that too.
FAQs
KraftMaid roofing parts installed in San Antonio typically last 12 – 18 years depending on sun exposure, hail frequency, and whether the flashing was seated correctly at install. San Antonio’s UV load and hailstorm frequency mean the bottom of that range is more common here than in, say, Ohio – and we factor that into our recommendations.
Yes – flashing, vent collars, drip edge, and isolated shingle failures are typically repairable without replacing the surrounding roofing. The repair involves removing the failed component, cleaning the underlying surface, installing the new part with the correct gauge match, and resealing. Call (432) 547-6806 for an assessment and a written quote – we won’t sell you a new roof because a vent boot cracked.
Most flashing, shingle, and vent collar replacements take 2 – 4 hours on-site, including testing the repair with light water spray. Larger flashing runs around chimneys or sidewalls can take a full day, and we’ll tell you that before we start. You get before-and-after photo updates of the repair per The Relay Visibility Guarantee.
We stock common KraftMaid-compatible flashing profiles, vent collars, drip edge, and shingle-match material on our trucks, so most repairs don’t need a parts order. If your job needs a specialty aftermarket part we don’t have, we order it and schedule the install once it arrives – usually 2 – 3 days in San Antonio.
Written by Luca Romano, Owner, Sawyer Remodel San Antonio at Sawyer Remodel San Antonio, serving San Antonio and nearby areas.
